client: wire record_time (cfg[64] f32_BE) and sample_rate (cfg[52] u16_BE)

Both offsets identified from _cfg_diagnostic scan on BE11529:
  cfg[64] float32_BE = 3.0  → record_time in seconds
  cfg[52] uint16_BE  = 1024 → sample_rate in Sa/s

Values are plausible but NOT yet validated by changing device settings
and re-reading.  Marked as ✅ candidate in docstring — confirm and
remove the ⚠️ note once a device-side change is observed here.

minimateplus/client.py

@@ -583,16 +583,20 @@ def _decode_compliance_config_into(data: bytes, info: DeviceInfo) -> None:
     The *data* argument is the raw bytes returned by read_compliance_config()
     (frames B+C+D concatenated, echo headers stripped).
 
-    Confirmed field locations (BE11529 with 3-step read, 2126 bytes):
+    Confirmed field locations (BE11529 with 3-step read, duplicate detection):
       - cfg[89]  = setup_name: first long ASCII string in cfg[40:250]
-      - cfg[??]  = record_time: float32 BE — offset TBD (scan below)
+      - cfg[64]  = record_time: float32 BE (BE11529 shows 3.0 s) ✅ candidate
-      - cfg[??]  = sample_rate: uint16 or float — offset TBD (scan below)
+      - cfg[52]  = sample_rate: uint16 BE (BE11529 shows 1024 Sa/s) ✅ candidate
       - "Project:"    needle → project string
       - "Client:"     needle → client string
       - "User Name:"  needle → operator string
       - "Seis Loc:"   needle → sensor_location string
       - "Extended Notes" needle → notes string
 
+    ⚠️  record_time and sample_rate offsets are confirmed candidates from
+    diagnostic scan but have NOT yet been validated by changing device settings
+    and re-reading.  Mark as ✅ once validated.
+
     Modifies info.compliance_config in-place.
     """
     if not data or len(data) < 40:
@@ -619,11 +623,16 @@ def _decode_compliance_config_into(data: bytes, info: DeviceInfo) -> None:
     except Exception as exc:
         log.warning("compliance_config: setup_name extraction failed: %s", exc)
 
-    # ── Record Time (⚠️ OFFSET UNCONFIRMED — waiting on diagnostic output) ──
+    # ── Record Time — float32 BE at cfg[64] ──────────────────────────────────
-    # Previous guess of 0x28 was wrong (that offset holds "(L)" string).
+    # Diagnostic confirmed: cfg[64] float32_BE = 3.0 on BE11529 (set to 3 s).
-    # The correct offset will be clear once _cfg_diagnostic identifies it.
+    # Previous guess of 0x28 was wrong (that offset holds the "(L)" label string).
-    # Temporarily disabled to avoid returning a garbage value.
+    # ⚠️  Validate by changing device record time and re-reading — mark ✅ once confirmed.
-    config.record_time = None   # TODO: set once offset confirmed from diagnostic
+    try:
+        if len(data) > 68:
+            config.record_time = struct.unpack_from(">f", data, 64)[0]
+            log.debug("compliance_config: record_time = %.3f s", config.record_time)
+    except Exception as exc:
+        log.warning("compliance_config: record_time extraction failed: %s", exc)
 
     # ── Project strings ───────────────────────────────────────────────────────
     try:
@@ -655,8 +664,15 @@ def _decode_compliance_config_into(data: bytes, info: DeviceInfo) -> None:
     except Exception as exc:
         log.warning("compliance_config: project string extraction failed: %s", exc)
 
-    # ── Sample rate (⚠️ OFFSET UNCONFIRMED — waiting on diagnostic output) ────
+    # ── Sample Rate — uint16 BE at cfg[52] ───────────────────────────────────
-    config.sample_rate = None   # TODO: set once offset confirmed from diagnostic
+    # Diagnostic confirmed: cfg[52] uint16_BE = 1024 on BE11529 (standard mode).
+    # ⚠️  Validate by changing device sample rate and re-reading — mark ✅ once confirmed.
+    try:
+        if len(data) > 54:
+            config.sample_rate = struct.unpack_from(">H", data, 52)[0]
+            log.debug("compliance_config: sample_rate = %d Sa/s", config.sample_rate)
+    except Exception as exc:
+        log.warning("compliance_config: sample_rate extraction failed: %s", exc)
 
     info.compliance_config = config
 

minimateplus/protocol.py

@@ -466,6 +466,11 @@ class MiniMateProtocol:
         ]
 
         config   = bytearray()
+        # Track (page_key, chunk_size) pairs to detect when frame D returns the
+        # same page/size as frame B — observed on BE11529 when the device is
+        # busy or connection state is fresh.  Duplicate chunks inflate the cfg
+        # and mis-align field offsets, so we drop them.
+        seen_chunks: set[tuple[int, int]] = set()
 
         for step_name, step_offset, step_params in _STEPS:
             log.debug(
@@ -485,10 +490,22 @@ class MiniMateProtocol:
                 continue
 
             chunk = data_rsp.data[11:]
+            page  = data_rsp.page_key
+            key   = (page, len(chunk))
+
+            if key in seen_chunks:
+                log.warning(
+                    "read_compliance_config: frame %s  page=0x%04X  data=%d  "
+                    "cfg_chunk=%d  DUPLICATE — skipping",
+                    step_name, page, len(data_rsp.data), len(chunk),
+                )
+                continue
+
+            seen_chunks.add(key)
             log.warning(
                 "read_compliance_config: frame %s  page=0x%04X  data=%d  "
                 "cfg_chunk=%d  running_total=%d",
-                step_name, data_rsp.page_key, len(data_rsp.data),
+                step_name, page, len(data_rsp.data),
                 len(chunk), len(config) + len(chunk),
             )
             config.extend(chunk)