Adds a production-safe headphone-splitter mode:
- Device bytes tee'd to both --upstream (primary/prod) and --mirror (new server)
- Only primary server responses are returned to the device
- Mirror connect/write failures are non-fatal and logged; prod is unaffected
- New raw_mirror_<ts>.bin capture file alongside raw_client/raw_server
Three modes: standalone (capture only), bridge (one upstream), splitter (two).
Default listen port changed to 12345 to match project ACH setup.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- bridges/ach_bridge.py: transparent TCP bridge that MITMs the MiniMate Plus
call-home connection — forwards to real ACH server while logging all frames
to raw_client/raw_server .bin files compatible with parse_capture.py;
standalone capture mode for lab use without a real server
- bridges/serial_watch.py: RS-232 serial monitor with live S3 frame parsing;
taps the line between MiniMate and modem (RV50/RV55); captures raw bytes,
.log and .jsonl; --ack-ok mode auto-replies to AT commands; fixed fatal
indentation bug in the original that silently prevented any data capture
- seismo_lab.py: new "Serial Watch" fourth tab (SerialWatchPanel) wrapping
serial_watch.py functionality; COM port picker with refresh, baud config,
ack-ok toggle, colour-coded live frame log (teal frames / yellow ctrl /
blue AT), raw .bin capture auto-fed into Analyzer tab on stop
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
section[6] is the monitoring flag (was wrongly section[1] — section[1] is always
0x00 in both states). Battery and memory fields use relative-from-end offsets
(section[-11:-9], section[-9:-5], section[-5:-1]) instead of absolute positions,
which broke when the payload grew by 3 bytes in monitoring mode.
Confirmed from full byte diff of 142 0xE3 frames in 4-8-26/2ndtry capture.
SFM start_monitoring now polls /device/monitor/status every 5s for up to 60s
instead of a fixed 25s delay (unit runs ~40s on-device sensor check before
confirming monitoring state).
Also corrects stale 1C→6E response anomaly claim in protocol reference — no
exceptions to the 0xFF−SUB rule are known.
- Introduced new SUBs for monitoring status, start, and stop commands in protocol.py.
- Implemented read_monitor_status, start_monitoring, and stop_monitoring methods in MiniMateProtocol class.
- Added new API endpoints for monitoring status retrieval and control in server.py.
- Enhanced the web application with a monitoring panel, including battery and memory status display.
- Created a new Python script to parse SUB 0x1C response frames for monitoring status.
- Documented the monitoring status response format and field locations in markdown and text files.
Frame index 9 was assumed to be the device terminator based on the
9-frame original blast capture. For streams with >9 frames (current
device produces 35), fi==9 is live waveform data — the skip was
dropping ~133 sample-sets per event.
Terminator detection is handled upstream via page_key==0x0000 in
read_bulk_waveform_stream, so no index-based skip is needed here.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds §7.8.4 to protocol reference and corresponding CLAUDE.md sections:
- End-of-stream: device sends exactly 1 raw byte after last chunk; handled
via TimeoutError + bytes_fed>0 check → graceful break to termination
- Chunk timing: ~1s per chunk, 35 chunks for a 9,306-sample event, safe
timeout is 10s (not default 120s)
- fi==9 decoder bug: hardcoded skip drops ~133 sample-sets per event;
noted as known issue pending fix
- ADC conversion: counts × (range/32767) → physical units (in/s for geo)
Changelog entries added for all four items (2026-04-06).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Two improvements to eliminate the ~2-min-per-event wait and unnecessary
full-event-list download when only one event is requested:
1. protocol.py: pass timeout=10.0 to _recv_one in the 5A chunk loop.
Device responds within ~1s per chunk; 10s gives a safe 10x buffer.
End-of-stream detection (raw_bytes=1) now fires in 10s instead of 120s,
cutting ~110s of dead wait per event.
2. client.py: add stop_after_index parameter to get_events(). When set,
iteration stops immediately after the target event is collected — no
further 0A/1E/0C/5A/1F cycles for events the caller doesn't need.
3. server.py: pass stop_after_index=index to both /device/event/{idx}
and /device/event/{idx}/waveform endpoints so a single-event request
only downloads that one event.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
When the device finishes streaming waveform data, it sends a single
partial byte (raw_bytes=1) rather than a complete A5 frame, then goes
silent for the full 120s timeout.
Observed: 35 chunks succeed, chunk 36 times out with raw_bytes=1 —
identical for both events in the test run.
Fix: on TimeoutError, if bytes_fed > 0 and we already have collected
frames, treat it as natural end-of-stream and break to the termination
step rather than propagating the exception. True transport failures
(raw_bytes=0, no prior frames) still raise.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Wraps each recv_one call in a try/except TimeoutError, logging:
- On timeout: chunk_num, counter, raw bytes_fed (distinguishes "device
silent" from "device sent unparseable bytes")
- On success: chunk_num, page_key, data_len, contains_Project flag
Parser is explicitly reset before each chunk recv so bytes_fed is
accurate per-chunk rather than cumulative. Helps identify exactly which
chunk fails and whether the device is responding at all.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Added `_decode_a5_waveform()` to parse SUB 5A frames into per-channel time-series data.
- Introduced `download_waveform(event)` method in `MiniMateClient` to fetch full waveform data.
- Updated `Event` model to include new fields: `total_samples`, `pretrig_samples`, `rectime_seconds`, and `_waveform_key`.
- Enhanced documentation in `CHANGELOG.md` and `instantel_protocol_reference.md` to reflect new features and confirmed protocol details.
Add read_bulk_waveform_stream() to MiniMateProtocol and wire it into
get_events() so each event gets authoritative client/operator/sensor_location
from the A5 frames recorded at event-time, not the current compliance config.
- framing.py: bulk_waveform_params() and bulk_waveform_term_params() helpers
(probe/chunk params and termination params for SUB 5A, confirmed from
1-2-26 BW TX capture)
- protocol.py: read_bulk_waveform_stream(key4, stop_after_metadata=True) —
probe + chunk loop (counter += 0x0400), early stop when b"Project:" found
(A5[7] of 9), then sends termination at offset=0x005A
- client.py: _decode_a5_metadata_into() needle-searches concatenated A5 frame
data for Project/Client/User Name/Seis Loc/Extended Notes; get_events() now
calls SUB 5A after each SUB 0C, overwriting project_info with event-time values
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
claude